这UMI 7764(零件号:777978-02)能够连接NI-735x/734x/733x运动控制器与第三方动力传动装置SH68-C68-S电缆。可用的电缆长度尺寸有0.5米、1米或2米UMI 7764运动控制器还可以与无刷伺服驱动器一起使用，如AKD-P00606。当接口与AKD-P00606一起使用时，需要一个2.5米的通道来驱动AKD电缆(零件号:781527-01).这倪UMI-7764还需要+5 V电源，例如镍PS-6(零件号:780577-01).另一个可以与该接口一起使用的产品是SCB-68用于数字输入/输出连接。

这UMI-7764具有主机总线监视器电源联锁，如果主机关闭或接口电缆断开，该联锁会自动关闭驱动器。这UMI 7764National Instruments是一种4轴通用运动接口，配有螺丝端子连接器。其运动/轴类型有:有刷伺服、无刷伺服、P指令伺服步进机。该接口具有信号通过兼容性和正交(正交编码器速率为1至20 MHz)、增量输入。这UMI-7764最适合实验室和工业应用。

链接到的每个轴镍UMI-7764通用运动接口有一个motion I/O端子板，这些信号连接到该端子板:分布式电源连接、放大器/驱动器连接、限位开关连接和编码器连接。每个轴都有五个驱动连接端子:Dir(逆时针)、模拟输出、Step(顺时针)、模拟输出接地和禁止输出。这NI-733x运动控制器没有模拟输出或模拟输出接地信号。

该装置有一个62针D-SUB I/O连接器、一根SCD-C68-S电缆和68针VHDCI偏置公连接器(用于将数字I/O连接器连接到NI SCB-68)。这UMI-7764在NI motion软件上运行，该软件要求存在LabVIEW等应用环境)。该器件与NI 735x、734x、733x运动控制器兼容。该设备的尺寸为7.7 x 6.0 x 1.8英寸。

The UMI 7764 (Part Number: 777978-02) has the capability to connect the NI-735x/734x/733x Motion Controllers to third-party power drives with the SH68-C68-S Cable. The cable length sizes available are 0.5 m, 1 m, or 2 m. The UMI 7764 Motion Controller can additionally be used with a brushless servo drive like the AKD-P00606. When the interface is used with the AKD-P00606, it requires a 2.5 m access to drive AKD cable (Part Number: 781527-01). The NI UMI-7764 also requires a +5 V Power Supply, such as the NI PS-6 (Part Number: 780577-01). Another product that can be used with this interface is the SCB-68 for digital I/O connection.

The UMI-7764 has a host bus monitor power interlock that automatically deactivates the drive if the host computer turns off or the interface cable is detached. The UMI 7764 National Instruments is a 4-axis Universal Motion Interface with screw terminal connectors. Its motion/axis types are: brushed servo, brushless servo, P-Command servo stepper. This interface has signal pass-through compatibility and quadrature (with quadrature encoder rates of 1 to 20 MHz), incremental inputs. The UMI-7764 is best for laboratory and industrial applications.

Every axis linked to the NI UMI-7764 Universal Motion Interface has a motion I/O terminal block to which these signals are wired: distributed power connections, amplifier/drive connections, limit switch connections, and encoder connections. Every axis has five terminals for drive connections: Dir (CCW), Analog Output, Step (CW), Analog Output Ground, and Inhibit Output. The NI-733x Motion Controllers do not have Analog Output or Analog Output Ground signals.

The device has a 62-pin D-SUB I/O connector, a SCD-C68-S cable with 68-pin VHDCI offset male connectors (and is used in connecting the digital I/O connector to the NI SCB-68. The UMI-7764 operates on the NI motion software which requires the presence of an Application Environment such as LabVIEW). The device is compatible with the NI 735x, 734x, 733x motion controllers. The device has the dimensions 7.7 x 6.0 x 1.8 inches.