只有具备适当资格的人员才能从事运输、装配、调试和维护。具备适当资格的人员熟悉运输、装配、安装、调试的人员并能操作电机，并具有相应的工作资格。合格人员必须了解并遵守以下标准和规范
规定:IEC 364标准。CENELEC HD 384或DIN VDE 0100iec报告664或DIN VDE 0110国家安全及事故预防条例或bgva3
在组装和调试之前，请阅读可用的文档。不正确的操作电机可能会对人员和机器造成伤害和损坏。严格遵守技术数据和连接信息要求(铭牌和文件)。
这是至关重要的，你要确保电机外壳是安全接地的开关柜内PE(保护接地)母线。电气安全是不可能的无低电阻接地连接。操作时请勿拔下任何连接器。这会造成死亡的危险
严重的伤害或广泛的物质损害。即使电机不旋转，电源连接也可能是带电的。从来没有
当设备通电时，断开电机的电源连接。这可能导致闪络，导致人员受伤和设备损坏联系人。
断开伺服放大器与电源电压的连接后，至少等待5秒在接触正常带电部件(如触点、螺丝连接)或打开任何连接。伺服放大器中的电容器仍然可以携带高达5的危险电压切断电源电压几分钟后。为了安全起见，测量直流电路电压，等待电压降到40V以下。电动机的表面在运行时可能非常热，根据他们的保护的范畴。表面温度可达100℃。测量温度，并等待，直到电机已冷却至40℃以下触摸它。

6SM57M-3.000

Only suitably qualified personnel are allowed to carry out transportation, assembly, commissioning and maintenance. Personnel with appropriate qualifications Familiar with transportation, assembly, installation, commissioning personnel and can operate the motor, and have the corresponding work qualifications. Qualified personnel must understand and comply with the following standards and specifications
Specification :IEC 364 standard. CENELEC HD 384 or DIN VDE 0100iec Report 664 or DIN VDE 0110 National Safety and Accident Prevention Regulations or bgva3
Before assembling and debugging, read the available documentation. Improper operation of the motor may cause injury and damage to people and machines. Strictly comply with technical data and connection information requirements (nameplates and documents).
It is vital that you ensure that the motor housing is securely grounded to the PE(protective ground) bus bar inside the switchgear. Electrical safety is impossible without a low resistance ground connection. Do not unplug any connector during operation. This poses a risk of death
Serious injury or extensive material damage. The power connection may be live even if the motor is not rotating. Never have
When the device is powered on, disconnect the power connection of the motor. This can cause flashover, resulting in injury to personnel and damage to equipment contacts.
After disconnecting the servo amplifier from the supply voltage, wait at least 5 seconds before contacting normal live parts (such as contacts, screw connections) or opening any connections. The capacitors in the servo amplifier can still carry up to 5 dangerous voltages after cutting off the supply voltage for a few minutes. For safety, measure the DC circuit voltage and wait for the voltage to drop below 40V. The surfaces of motors may be very hot during operation, depending on the category of their protection. The surface temperature can reach 100℃. Measure the temperature and wait until the motor has cooled to below 40 ° C by touching it.