VMI ACC-5595，ACC-5595-208,GE交换机 技术参数

ACC-5595-208,GE交换机 VMI ACC-5595
技术参数: acc – 5595 2gb /s反射内存集线器组装
特性 ：
•用于GE智能平台5565 反光记忆网络产品
•使用小型形式，最多可提供8个端口 SFP (factor pluggable)光模块
•集线器组件可以级联 最大256个节点
•自动绕过光纤网络中有缺陷或断开的节点
•可选择自动旁路 由信号的丢失或由 同步模式丢失
•每个端口再生串口光 信号，消除链路损耗和减少抖动
•可配置为ac -5595是一个管理集线器设计 与GE智能平台合作
5565系列的实时反射存储器 网络产品。
反射内存 集线器可以自动绕过端口时 它检测到信号丢失或失效 同步模式，
允许其他模式 网络中的节点保持运行状态。
因为是光接口 使用小型SFP (small form factor pluggable)收发器，
只需要使用所需的端口 填充。ac -5595 SFP光模块 可以是多模的组合
(短距离)或单模ac -5595作为一个选项可以配置 19英寸1U机架式机箱或 作为桌面框。
普遍的权力 供应允许操作几乎任何 国际电力标准。
acc-5595自动旁路端口 当没有有效的同步时 模式检测。
三个led，相邻 每个端口，提供一个可视化的指示 端口状态。
附加状态指示和 操作模式可通过 串口或以太网端口。 状态信息包括对的检测 安装收发器

ACC-5595 2 Gb/s Reflective Memory Hub Assembly Features • For use with GE Intelligent Platforms 5565 Reflective Memory network of products • Provides up to eight ports using small form factor pluggable (SFP) transceivers • Hub assemblies can be cascaded with a maximum of 256 nodes • Automatically bypasses defective or disconnected nodes in a fiber-optic network • Automatic bypass can be optionally controlled by the loss of signal or by the loss of sync pattern • Each port regenerates the serial optical signal, eliminating link losses and reducing jitter • Configurable for use with cables up to 10 km in length • 10BaseT Ethernet TCP/IP port for remote access and control • RS232 port for local access and control • Optional 19 – inch 1U rack mount or desktop enclosure • Internal universal power supply • Dark on Dark option turns off the board’s transmitter if the receiver does not detect a signal (available for firmware versions 02.00 and later) The ACC-5595 is a managed hub designed to operate with the GE Intelligent Platforms 5565 family of Reflective Memory real-time network products. The Reflective Memory hub can automatically bypass ports when it detects a loss of signal or the loss of valid synchronization patterns, allowing the other nodes in the network to remain operational. Since the optical ports are implemented with small form factor pluggable (SFP) transceivers, only the required ports need to be populated. The ACC-5595 SFP transceivers can be a combination of either multimode (short distance) or single-mode (long distance) transceivers. This feature permits a cost saving in small networks as well as system optimization. For larger networks, several ACC-5595 assemblies can be cascaded, permitting a managed hub array with up to 256 nodes. Each port regenerates the serial optical signal, eliminating the problems with insertion losses and cable attenuation. Signal regeneration also reduces jitter. The RS232 port gives you the ability to monitor and control your Reflective Memory network through a simple PC serial port. The Ethernet port feature allows you to monitor and control the hub from great distances through a local area network (LAN) or via a Web browser.